用离子速度影象技术研究n-C4H9Br的光解

利用离子速度影象技术研究了正一溴丁烷(n-C4H9Br)在231~267 nm波段的光解,得出了如下结论:正一溴丁烷(n-C4H9Br)在231~267 nm波段的吸收源于基态到三个最低激发态的跃迁,这三个激发态标识为1A″、2A′和3A′;发生在这三个排斥态的势能面(PES)上的光解最终导致C4H9 Br(2P3/2)或C4H9 Br*(2P1/2)的产生;2A′和3A′态之间存在避免交叉(Avoided crossing)会影响最终的光解产物;从基态1A′到激发态1A″的跃迁矩垂直于对称面,也就垂直于C-Br键;从基态1A′到激发态3A′的跃迁矩平行于对称面,同时平行于C-Br键;从基态1A′到激发态2A′的跃迁矩在对称面内,且与C-Br键成53.1°夹角.我们也讨论了正一溴丁烷(n-C4H9Br)在234 nm和267 nm附近光解时的避免交叉几率(Avoided crossingprobability),以及它对单通道相对产额(Relative fraction of the individual pathways)的影响.     

红外动态图像生成技术概念研究

红外动态图像生成技术的基本概念包括基本术语及其定义。为了描述红外动态图像生成技术的特性,通常采用如光源类型、光谱波段、阵列规模、空间分辨率、填充因子、时间常数、帧频、闪烁、温度范围、串扰、均匀性、发射率、辐射对比度、动态范围、温度分辨率、调制传递函数、几何畸变及最大温度和最大辐射强度等概念。介绍了描述红外动态图像生成系统性能的基本概念的定义。转换器的指标定义对于转换器的设计和性能指标的测试都有重要的意义。     

“阳”加速器钼丝X-pinch初步实验研究

 在“阳”加速器上进行了直径分别为10, 15, 20 μm, 交叉角为32°,45°,60°的钼（Mo）丝X-pinch实验。“阳”加速器产生的电流峰值约520 kA，上升时间80 ns。实验中通过X射线功率谱仪和纳秒分幅相机等仪器对Mo丝X-pinch辐射特性进行了诊断。实验表明：Mo丝X-pinch过程中会出现多次X射线爆发，箍缩过程中产生的热点辐射出能量超过3 keV的X射线，探测到的最小热点直径小于30 μm。     

同步辐射X射线衍射增强CT方法研究

本文将同步辐射硬X射线衍射增强成像方法应用于材料无损检测CT方法中（简称衍射增强CT法），并对自制样品进行投影成像重建，获得了非常清晰的样品内部结构图像,并与样品的单晶吸收成像CT重建结果进行对比.结果表明，对于吸收系数相近的结构材料,衍射增强CT法可得到更好的物质内部边界.     

气垫导轨上运动物体加速度测量方法的改进

利用计数计时测速仪测量气垫导轨上滑块运动的加速度,其测量精度直接依赖于2个光电门之间距离的测量,而在实验中该距离的测量往往不易达到很高的精度,致使加速度的测量精度不高.对计数计时测速仪的电路和单片机程序稍加修改,使之能测出滑块从一个光电门运动到另一个光电门所需时间,就无需测量2个光电门之间的距离,因而提高了加速度的测量精度,节约单片机的资源并缩短运行时间.     

光学三维成像实验系统

建立光学投影层析三维成像系统,该系统包括光学成像、图像采集、断层重建及三维显示,重建算法为滤波反投影算法.实验结果表明:利用该系统得到的重建图像与样品的形状吻合,重建结果边缘清晰,伪迹较小.     

荧光波长对共焦显微镜成像特性的影响

导出了共焦显微镜中不同荧光波长情况下的荧光功率传输函数、三维脉冲响应函数（3D－PSF）和三维光学传递函数（3D－OTF）。结果表明，不同的荧光波长对共焦显微镜的空间截止频率、分辨率、光学传递函数存在明显的影响。当激发波长与荧光波长的比值下降到一定程度时，可以看到明显的失锥现象。     

Determination of the boiling point distribution of sulfur compounds in light cycle oil using GC with a flame photometric detector and pyrolyzer

A method has been developed to determine the boiling point distribution of sulfur compounds in light cycle oils (LCO'S). The method chosen for this analysis was GC with a flame photometric detector (FPD) and pyrolyzer. Tests were carried out to evaluate the recovery efficiency, repeatability, and accuracy of the method. Repeatabilities within 2% were obtained. The recovery of benzothiophenes and dibenzothiophenes was close to 100%; this was important because these are the major sulfur components in LCO's. No hydrocarbon or solvent interferences were observed with the use of the pyrolyzer, even for a 95% solvent level. Comparison with results from other techniques showed that the method accurately determined the levels of sulfur compounds in the LCO boiling point range.     

Nitro musks in cosmetic products—determination by headspace solid-phase microextraction and gas chromatography with atomic-emission detection

Summary The combination of headspace solid-phase microextraction with atomic-emission detection enables highly selective and sensitive determination of itro musk compounds in cosmetic products. Sample preparation is considerably simplified; there is no solvent extraction step. Enrichment is influenced by the type and amount of cosmetic product investigated. The lowest amount giving well detectable peaks is 1 mg musk compound per kg sample. Calibration curves obtained from spiked solutions of selected reference cosmetics in water show very good linearity. Relative standard deviations of peak areas from repeated measurements are usually <10%. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Near-field thermoelastic imaging coupled with infrared detection

Near-field thermoelastic imaging is a simple way to investigate the thermal and coupled thermoelastic properties of materials. A few microscopes, deriving from the atomic force microscope, have been used to observe and to quantify the samples observed. But the main problem is the absolute measurement of the temperature, because surface topography and thermal expansion contributions are not easily discernible. In the proposed SThEM (scanning thermoelastic microscope), the tip is excited at the resonance frequency of the cantilever and the sample is periodically heated by the Joule effect. Thus the static contributions (drift, topography) are reduced. Moreover, a radiometric sensor, operating in the far field, has been added in order to quantify the temperature. This multi-acquisition microscope enables one to investigate small objects at the nanoscale with complementary information at the micrometric scale.